![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en082.png)
Installing the Hard Disk Drive
Refer to the following steps if you need to install a new HDD (hard disk
drive) of your Notebook PC.
IMPORTANT! Purchase an HDD from authorized retailers of this Notebook
PC to ensure maximum compatibility and reliability.
WARNING! Disconnect all the connected peripherals, any telephone or
telecommunication lines and power connector (such as external power
supply, battery pack, etc.) before removing the compartment cover.
NOTES:
• The appearance of your Notebook PC’s bottom side and HDD may
vary per model but the HDD installation remains the same.
• It is recommended that you replace the HDD under professional
supervision. You may also visit an authorized service center for
further assistance.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en083.png)
Notebook PC E-Manual
83
A.
Loosen the screw from the Notebook PC’s compartment cover.
B.
Pull out the compartment cover and remove it completely from
your Notebook PC.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en084.png)
84
Notebook PC E-Manual
C.
Remove the screws securing the HDD bay to the compartment.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en085.png)
Notebook PC E-Manual
85
D.
(optional) If an HDD is currently installed in your Notebook PC,
disconnect the HDD bay from the HDD port as shown in the
illustration below.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en086.png)
86
Notebook PC E-Manual
HDD bay
E.
Use the flap on the HDD bay to pull it out of the compartment.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en087.png)
Notebook PC E-Manual
87
F.
(optional) If an HDD is currently attached to the HDD bay, refer to
to the following steps on how to remove the old HDD:
1.
Remove all the screws on the sides of the HDD bay.
2.
Remove the old HDD from the HDD bay then place it on a
flat dry surface with its PCB (printed circuit board) facing up,
as shown in the illustration below.
old HDD
HDD bay
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en088.png)
88
Notebook PC E-Manual
G.
Place the new HDD with its PCB (printed circuit board) facing the
HDD bay. Ensure that the port connectors of your HDD are not
obstructed by any part of the HDD bay.
H.
Reattach and secure the HDD with the screws you removed
earlier.
new HDD
HDD bay
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en089.png)
Notebook PC E-Manual
89
I.
Replace the HDD bay back in the compartment, with the HDD
connector aligned with the Notebook PC’s HDD port. Push the
HDD bay until it connects with the Notebook PC.
J.
Secure the HDD bay with the screws you removed earlier.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en090.png)
90
Notebook PC E-Manual
K.
Align and replace the cover of the compartment.
L.
Reattach and secure the cover using the screw you removed
earlier.
![background image](https://i.rogdoc.com/ASUS ROG GL552VX/en/ASUS ROG GL552VX_en091.png)
Notebook PC E-Manual
91